Precautions when using the oven

safe question
1. Pay attention to cleaning when using the electric oven for the first time
Wipe the inside and outside of the oven with a clean damp cloth first to remove some dust. Then you can use the oven to bake at high temperature for a while, and sometimes white smoke may come out vacuum cleaner motor , which is normal. After baking, pay attention to ventilation and heat dissipation.
2. After cleaning, the electric oven can be used normally
Before baking any food, preheat to the specified temperature to match the baking time in the recipe. It takes about 10 minutes to preheat the oven. If the oven is preheated for too long, it may also affect the service life of the oven.
3. Be careful with the oven being heated to avoid burns
In addition to the heat inside, the case and glass door are also hot, so be careful when opening or closing the oven door to avoid getting burned by the glass door. Always use the handle when placing the pan in or out of the oven and never touch the pan or food directly with your hands. Do not touch the heater or other parts of the oven cavity with your hands to avoid burns.
4. When the oven is in use, the temperature should be adjusted first
When the oven is in use, the temperature should be adjusted to the upper and lower heat, and the upper and lower heat should be adjusted, and then turn the time knob clockwise (do not turn it counterclockwise). At this time, the power indicator lights up, which proves that the oven is working. state.
In the process of use, if we set the food to be baked for 30 minutes, but through observation, the food is baked in 20 minutes, then we do not turn the time knob counterclockwise at this time, please adjust the fire position in the middle of the three knobs to off That's it, so it can extend the life of the machine. This is different from microwave usage, which can be reversed.

5. After each use, it should be cleaned after cooling down
It should be noted that when cleaning the door and the oven cavity shell, it should be wiped with a dry cloth, and should not be washed with water. In case of hard-to-remove dirt, it can be gently wiped off with detergent. Other accessories of the electric oven such as baking trays, grilling nets, etc. can be washed with water.
6. The oven must be placed in a ventilated place
Do not lean too far against the wall to facilitate heat dissipation. Moreover, it is best not to place the oven near the water source, because the overall temperature of the oven is very high when working, and if it touches water, it will cause a temperature difference.
7. When the oven is working, do not stay in front of the oven for a long time
Do not stand in front of the oven for long periods of time. If the glass door of the oven is found to be cracked, please stop using it immediately.
Oven Heater Features:
● Thermostat: imported from Japan [OMRON] touch-type digital display dual-group P.I.D. microcomputer automatic calculation type.
● Circulating pump: It adopts a special specification pump of the same type as the European imported mold temperature machine, and controls two different temperatures through a single pump. It provides high pressure, reduces temperature difference and saves electricity. Reduce space and reduce costs.
● Appearance design: The patented separate control box design completely cuts off the intrusion of water vapor, oil and gas heat, and prolongs the life of electrical parts.
● Mechanical and electrical materials: imported parts and components such as French "TELEMECANIQUE" and Japanese [FUJI] [OMRON], with a service life of 2 million times and a long service life.
● Circuit design: chain error-proof circuit and practical fault indication, completely protect the stable operation of the mold temperature machine.
● Pipeline design: 316 stainless steel integrally formed pipe, fully welded pipe design, acid and alkali resistance, small pipe loss, and even heating.
● Sweden imported electric heating wire, the heating and cooling speed is fast, and the temperature is more stable.

Name:	Heating Element Oven Heater 210
Material:	Magnet and  Stainless steel etc.
Processes	Casting. Welding,processing: etc.
Describe	Good material, small dimensional tolerance, good performance (suitability), and good surface quality.
QC	Dimensinal toleranceis available Technicians self-check in production Engineer spot check in production QC inspects after mass production finished Spot check before shipping
Packing	Foam box inside, paper carton outside, Reinforcement by bags and pallets to avoid the damage
Advantage	OEM service and Design service are available Min order and sample order is acceptable. Reply to your inquiries in 24 hours. Your detail requirements will be responded within 24 hours. Your needs will always be treated as our top priority. Delivery the high quality goods on time.